PLENTY Screen Set
Vape accessories
by Storz & Bickel
PLENTY Screen Set — Original Storz and Bickel Replacement Screens
The PLENTY Screen Set is a pack of six original manufacturer replacement screens designed for the Storz and Bickel PLENTY vaporiser. Screens clog, gunk up, and eventually restrict airflow — that's not a defect, it's just what happens when you vaporise regularly. These are the same screens that came with your PLENTY out of the box, made to the same spec, in the same factory. Swap them in, and your draw resistance drops back to day-one levels.
Which Variant Do You Need?
This is where most people pause, so here's the short version. Three options, each for a different setup:
| Variant | SKU | Diameter | Best for |
|---|---|---|---|
| Normal | VS0097 | 30 mm | Standard PLENTY filling chamber — the one most people use |
| Normal - Small | VS0175 | 15 mm | PLENTY filling chamber reducer — for smaller loads |
| Fine | VS0096 | 30 mm | Powdered or finely ground materials in the standard filling chamber |
If you've never swapped out the filling chamber reducer, you're using the standard 30 mm chamber — grab either Normal or Fine depending on your grind. If you use the reducer for solo sessions with smaller amounts, you want Normal - Small at 15 mm.
One honest note: the Fine screens restrict airflow slightly more than the Normal ones. That's by design — the tighter mesh stops fine particles from pulling through. If you're grinding coarsely, you don't need them. If you're working with powdered material, you absolutely do.
Specifications for PLENTY Replacement Screens
| Spec | Value |
|---|---|
| Manufacturer | Storz and Bickel |
| Compatible device | PLENTY Vaporiser |
| Quantity per set | 6 screens |
| Normal screen diameter | 30 mm |
| Normal - Small screen diameter | 15 mm |
| Fine screen diameter | 30 mm |
| Material | Stainless steel mesh (OEM) |
| Part type | Original manufacturer replacement |
Complete your PLENTY maintenance kit: pair these screens with the PLENTY Wear and Tear Set for a full refresh of seals and gaskets. If you're using the filling chamber reducer for smaller solo sessions, the PLENTY Dosing Capsule Set keeps your chamber cleaner between screen swaps.
Why Fresh PLENTY Screens Matter More Than You Think
We've had customers come in saying their PLENTY "doesn't hit like it used to." Nine times out of ten, the screens are the problem. Resin builds up in the mesh after a few weeks of regular use, and even a thorough soak in isopropyl alcohol doesn't fully restore a screen that's been through 50+ sessions. The mesh warps slightly, the holes narrow, and your draw resistance creeps up so gradually you don't notice until you pop in a fresh screen and wonder where that airflow's been hiding.
At six screens per set, you're looking at roughly 2-3 months of replacements if you swap every 2-3 weeks — which is what we'd recommend for daily users. Light weekend users can stretch a single screen to 4-6 weeks without noticing much degradation. The point is: screens are a consumable, not a permanent part. Storz and Bickel designed the PLENTY with easy screen access for exactly this reason.
One thing worth mentioning: third-party screens exist at lower prices, but the fit is often slightly off. We've seen generic 30 mm screens that sit loose in the chamber or don't lie perfectly flat, which creates gaps where material slips through. These are the original Storz and Bickel parts, stamped to the same tolerances as what shipped with your unit. For a part this cheap, it's not worth gambling on a knockoff.
How to Replace PLENTY Vaporiser Screens
- Let your PLENTY cool completely — the filling chamber retains heat for several minutes after a session.
- Remove the filling chamber from the unit by unclipping the top section.
- Use the included Storz and Bickel cleaning brush or a small flathead tool to gently lift the old screen out of its seat. If it's gunked in, a 10-minute soak in isopropyl alcohol (90%+) loosens it.
- Brush out any residue from the chamber walls and screen seat. A clean seat means the new screen sits flush.
- Drop the new screen into the chamber — flat side down, making sure it sits evenly across the entire diameter. For the 30 mm Normal or Fine screens, it should rest snugly without any visible gaps at the edges. For the 15 mm Normal - Small, it seats into the filling chamber reducer.
- Reassemble the filling chamber and clip it back onto the PLENTY. Run a short empty heating cycle at your usual temperature to burn off any manufacturing residue on the new screen — takes about 30 seconds.
- Load your material and draw. You'll feel the difference in airflow immediately if the old screen was overdue for replacement.
