Flint Ignition Component
Lighters & torches
by Clipper
We'll only email you about this product — no marketing.
Clipper Flint Ignition Component
The Clipper flint ignition component is a ferrocerium-and-steel striking assembly that restores ignition to any standard Clipper lighter in under ten seconds. Rather than binning a perfectly good lighter when the spark dies, you pop out the old flint system, slot this one in, and you're back to full flame almost instantly. Over 85% of Clipper lighters discarded in Europe still have usable gas — the flint is the only failed part. It's the smallest purchase that saves the most waste — and the most frustration.
Why This Clipper Flint Component Earns Its Keep
The gas isn't empty, the body isn't cracked, the mechanism works — it just won't spark. That's a lighter with years of life left in it, heading to landfill over a component smaller than a pencil eraser.
This replacement flint ignition system slots directly into any standard Clipper lighter. Pull out the old flint wheel from the top of the lighter (it lifts straight out), swap in the fresh one, and you've got a reliable spark again. The flint itself is a ferrocerium rod — the same iron-cerium alloy that's been used in lighters since the early 1900s. According to materials data published by the European Chemical Agency (ECHA), ferrocerium typically contains around 50% cerium, 25% lanthanum, and the balance in iron and trace rare earths. It's hard enough to last through hundreds of strikes but soft enough to throw a fat spark every time the wheel catches it. You'll feel a satisfying resistance when you flick it — not the mushy, dead spin of a worn-out flint.
One honest note: these are sized specifically for Clipper lighters. They won't fit a Zippo or a generic disposable — Zippo flints measure approximately 2.4 mm in diameter versus Clipper's 2.0 mm, so cross-compatibility is zero. If you're running Clippers (and we'd say they're the best refillable lighter for daily use), order a few of these so you're never caught without a spark.
The Pokie Advantage
The Clipper flint assembly doubles as a 68 mm rigid poker — purpose-built for packing down a joint or clearing a clogged cone piece. Pull the flint assembly out by the striking wheel and you've got a thin, rigid poker that's exactly the right diameter for the job. No fumbling with matchsticks, no bending paperclips. It's one of those design touches that seems obvious once you know about it — but most people don't discover it until someone shows them.
When you replace the flint, you get a fresh pokie too. The new rod is straight, firm, and the right length. An old, nearly spent flint tends to wobble and bend. A fresh one packs cleanly and evenly every time.
Sustainability by the Numbers
A single refillable Clipper lighter lasts an average of 3 to 5 years with periodic flint and gas replacements. According to waste monitoring data referenced by the EMCDDA in their harm-reduction literature, disposable lighters represent a measurable fraction of plastic waste found in European waterways. Switching to a refillable system with replaceable flints reduces lighter-related plastic waste by an estimated 95% over a two-year period. Each Clipper flint weighs under 1 gram and contains no plastic — just metal and ferrocerium. Compare that to a disposable BIC at 21 grams of mixed plastic and metal that cannot be separated for recycling.
| Factor | Disposable BIC | Clipper + Flint Refills |
|---|---|---|
| Lifespan | 2–4 weeks | 3–5 years |
| Annual cost (daily smoker) | ~€50–€75 | ~€8–€12 (gas + flints) |
| Plastic waste per year | ~500 g | ~0 g |
| Recyclable | No (mixed materials) | Yes (metal body) |
| Built-in pokie | No | Yes |
| Spec | Value |
|---|---|
| Product | Clipper Flint Ignition Component |
| SKU | HS1427 |
| Compatibility | All standard Clipper lighters |
| Flint Material | Ferrocerium (iron-cerium alloy) |
| Flint Diameter | ~2.0 mm |
| Assembly Length | ~68 mm |
| Includes | Flint rod and striking wheel assembly |
| Secondary Use | Joint pokie / packing tool |
| Category | Lighters and Torches |
Complete your setup: pair this flint with Clipper lighter gas to fully refuel a tired Clipper. If you're rolling your own, a set of RAW rolling papers and filter tips rounds out the kit nicely — and that fresh pokie will earn its keep immediately. Browse our full Lighters and Torches category or check the Smoking Accessories wiki for more gear guides.
How to Replace Your Clipper Flint
Swapping the flint takes approximately 10 seconds and requires no tools, no force, and no prior experience. Here's the full process:
- Grip the striking wheel on your Clipper lighter and pull it straight upward. The entire flint assembly — wheel, spring, and flint rod — lifts out in one piece.
- Set the old assembly aside (or bin it if the flint is fully spent).
- Take the new Clipper flint ignition component and check the flint rod is seated in the assembly. It should be snug with the striking wheel sitting on top.
- Insert the new assembly back into the lighter body, flint-end first. Push it down until the striking wheel sits flush with the top of the lighter.
- Give the wheel a test flick. You should see a bright, consistent spark. If the lighter is also low on gas, refill through the valve on the base before testing the flame.
